Introduction

The Konica Minolta DF-629 is a reversing-type automatic document feeder (ADF) used with machines such as the bizhub C368.

When troubleshooting DF-629 paper jams, understanding the five document detection sensors and their operating sequence is essential. Different sensors monitor different stages of document feeding, registration, scanning and output. If a sensor does not change state within the expected time, the machine may generate a corresponding 66-XX jam code.

The DF-629 uses a single-CCD reversing scanning system rather than a dual-scan arrangement. For double-sided originals, the document must be scanned on the first pass, reversed and transported through the scanning path again to scan the reverse side.

This means that the sensor sequence during duplex operation is more complicated than during simplex feeding.

This guide explains the five DF-629 sensors, their DFCB I/O names, the normal paper feeding sequence, duplex reversal operation and the corresponding 66-XX jam codes for the bizhub C368 configuration described here.

Key Takeaways

  • The DF-629 uses five main document detection sensors: PS1, PS2, PS3, PS4 and PS5.
  • PS1 detects whether originals are present on the document tray; it does not belong to the main paper-path timing sequence.
  • The normal forward document path follows PS2 → PS3 → PS4 → PS5.
  • PS2 confirms document separation, PS3 controls registration, PS4 detects the document entering the scanning area, and PS5 detects document exit.
  • Duplex scanning requires the document to reverse and pass through the feeding path again.
  • Different sensor timing failures correspond to different 66-XX jam codes.
  • DFCB I/O monitoring is an effective way to identify which sensor is not changing state correctly.

1. DF-629 ADF System Overview

The DF-629 is a reversing-type ADF with a single CCD scanning system.

It is not a dual-scan document feeder. When scanning a double-sided original, the machine scans the front side first, reverses the document and then transports it through the scanning path again to scan the back side.

1.1 Simplex Document Feeding

For a single-sided original, the basic process is:

  1. The original is picked up from the document tray.
  2. The separation mechanism feeds one sheet into the transport path.
  3. The document passes through the registration section.
  4. The front side is scanned.
  5. The document continues to the exit section.
  6. The original is delivered to the output tray.

1.2 Duplex Document Feeding

For a double-sided original, the process is different:

  1. The original is picked up and separated.
  2. The front side is transported through the scanning area and scanned.
  3. After the first-side scan, the M4 reversing motor pulls the document back into the reversing section.
  4. The document is reversed.
  5. The document is transported forward again.
  6. The reverse side passes through the scanning area and is scanned.
  7. The document is delivered to the output tray.

Because the document passes through the feeding and scanning path twice, PS2, PS3 and PS4 participate in another sequence of sensor timing checks during the second pass.

This is an important difference between the DF-629 and the DF-704. Their document feeding and scanning arrangements should not be assumed to be identical.

2. DF-629: Five Sensor Functions and DFCB I/O Names

The DF-629 uses five main document detection sensors.

Sensor DFCB I/O Display Name Function
PS1 Document Empty Detects whether originals are present on the document tray
PS2 After Separate Detects the document after the separation mechanism
PS3 Registration Detects the document at the registration section
PS4 Document Reading Detects the document before the scanning slit
PS5 Document Exit Detects the document after scanning, before the output tray

2.1 PS1 – Document Empty Sensor

Location: Document tray

Function: Detects whether originals are present on the document tray.

When originals are placed on the tray:

  • PS1 = ON
  • The DFCB recognizes that documents are available and permits the feeding process to start.

After the first sheet is picked up and leaves the tray:

  • PS1 = OFF

PS1 is used for document presence detection. It is not part of the main paper-path jam timing sequence.

Possible abnormal conditions:

PS1 Condition Possible Symptom
Stuck OFF The panel continues to request that the user place originals on the tray, and feeding does not start
Stuck ON The machine continues to detect originals even when the tray is empty, potentially causing empty feeding attempts or incorrect counting

According to the DF-629 troubleshooting information described here, PS1 does not generate a 66-series paper jam code.

2.2 PS2 – After Separate Sensor

Location: Downstream of the separation roller and upstream of the registration section.

Function: Confirms that a document has successfully passed through the separation mechanism.

When the leading edge of a separated sheet reaches PS2:

  • PS2 = ON
  • The DFCB starts the relevant document transport timing check.

PS2 helps confirm successful document separation and can assist in identifying empty feeding or multiple-feed-related problems.

The trailing edge of the document eventually leaves PS2:

  • PS2 = OFF

A failure in the expected PS2 timing sequence may generate code 66-03.

2.3 PS3 – Registration Sensor

Location: Registration section.

Function: Detects the document at the registration position and supports document alignment.

After PS2 turns ON, the leading edge of the document reaches PS3:

  • PS3 = ON
  • The registration clutch operates to create a paper loop.
  • The loop helps compensate for feeding variations and align the document’s scanning start position.

As the document continues moving:

  • The trailing edge leaves PS2, causing PS2 = OFF.
  • The trailing edge later leaves PS3, causing PS3 = OFF.

PS3 is associated with two important jam codes:

  • 66-13
  • 66-23

These codes represent different sensor timing conditions.

2.4 PS4 – Document Reading Sensor

Location: Before the scanning slit.

Function: Detects the document entering the scanning area.

After PS3 turns ON, the document continues forward until its leading edge reaches PS4:

  • PS4 = ON
  • The machine starts the image-reading process.

After the trailing edge leaves the scanning area:

  • PS4 = OFF

If PS4 does not turn ON within the expected time after PS3 detection, the machine may generate code 66-33.

During duplex reversal, a separate timing condition may generate code 66-21.

2.5 PS5 – Document Exit Sensor

Location: After the scanning area and before the document output tray.

Function: Detects the document leaving the scanning section and entering the output path.

After PS4 turns ON, the leading edge reaches PS5:

  • PS5 = ON
  • The document has passed the scanning area and is being transported toward the output tray.

When the entire document leaves PS5:

  • PS5 = OFF
  • The single-sheet feeding process is completed.

If PS5 does not turn ON within the expected time after PS4 detection, the machine may generate code 66-04.

3. Normal Forward Paper Feeding Sequence

Understanding the normal sensor sequence is the foundation of DF-629 troubleshooting.

For a simplex original, the standard forward feeding sequence is:

<escape>PS1 → Document Pickup and Separation → PS2 → PS3 → PS4 → PS5</escape>

PS1 is a document-presence sensor and acts as a preliminary feeding condition. It is not part of the main transport timing chain.

The main paper-path sensor sequence is:

<escape>PS2 → PS3 → PS4 → PS5</escape>

Sensor Timing Summary

Sequence Sensor Expected Action
1 PS1 Detects originals on the document tray
2 PS2 Turns ON when the separated sheet reaches the sensor; timing check begins
3 PS3 Turns ON when the leading edge reaches registration; registration loop is formed
4 PS4 Turns ON when the document reaches the scanning area; image reading starts
5 PS5 Turns ON when the document reaches the exit section
6 PS5 Turns OFF after the entire sheet leaves the sensor

Important Timing Details

The machine does not simply check whether each sensor works. It also monitors whether the sensor changes state within the expected time after the previous transport event.

For example:

  • PS2 turns ON, but does not turn OFF within the expected time: possible 66-03.
  • PS2 has turned ON, but PS3 does not turn ON in time: possible 66-13.
  • PS2 turns OFF, but PS3 remains ON beyond the expected time: possible 66-23.
  • PS3 turns ON, but PS4 does not turn ON in time: possible 66-33.
  • PS4 turns ON, but PS5 does not turn ON in time: possible 66-04.

This timing relationship is useful for locating the section where document transport stops or sensor detection becomes abnormal.

4. DF-629 Sensor Failures and Corresponding 66-XX Jam Codes

The following table summarizes the sensor-related jam codes described for the DF-629 on the bizhub C368.

Sensor Sensor Name Jam Code Detection Logic and Possible Condition
PS1 Document Empty No 66-series code Stuck OFF: machine keeps requesting originals. Stuck ON: machine may detect originals when the tray is empty
PS2 After Separate 66-03 PS2 turns ON, but does not turn OFF within the expected time
PS3 Registration 66-13 PS2 has turned ON, but PS3 does not turn ON within the expected time
PS3 Registration 66-23 PS2 has turned OFF, but PS3 remains ON beyond the expected time
PS4 Document Reading 66-33 PS3 has turned ON, but PS4 does not turn ON within the expected time
PS4 Document Reading 66-21 Specific duplex reversing-stage timing error: after reversal and PS3 detection, PS4 does not turn ON within the expected time
PS5 Document Exit 66-04 PS4 has turned ON, but PS5 does not turn ON within the expected time

4.1 Error Code 66-03 – PS2 After Separate

Detection condition: PS2 turns ON, but does not turn OFF within the expected time.

Possible causes include:

  • Document stuck around the separation section.
  • PS2 actuator or flag stuck in the ON position.
  • Contamination around the sensor.
  • Sensor or wiring abnormality.

Check whether the document can move freely through the separation section and whether the PS2 actuator returns correctly.

4.2 Error Code 66-13 – PS3 Registration Does Not Turn ON

Detection condition: PS2 has turned ON, but PS3 does not turn ON within the expected time.

This means that the document has been detected after separation but has not reached the registration sensor as expected.

Possible inspection areas:

  • Document transport between PS2 and PS3.
  • Registration rollers.
  • Paper path obstruction.
  • PS3 actuator and sensor condition.
  • Sensor wiring and connections.

4.3 Error Code 66-23 – PS3 Registration Does Not Turn OFF

Detection condition: PS2 has turned OFF, but PS3 remains ON beyond the expected time.

This indicates that the trailing edge has left PS2, but PS3 continues to detect the document.

Possible causes include:

  • Document stuck around the registration section.
  • PS3 actuator unable to return.
  • Sensor contamination.
  • PS3 sensor or wiring abnormality.

4.4 Error Code 66-33 – PS4 Document Reading Does Not Turn ON

Detection condition: PS3 has turned ON, but PS4 does not turn ON within the expected time.

The document has passed the registration detection stage but has not reached the document reading sensor as expected.

Check:

  • The transport path between PS3 and PS4.
  • Document reading section rollers.
  • Paper obstruction.
  • PS4 actuator and sensor condition.
  • Sensor wiring and connections.

A similar 66-33 condition may also occur during the second forward feeding pass in duplex operation. However, the reversing-stage-specific condition described in this repair information is associated with 66-21.

4.5 Error Code 66-04 – PS5 Document Exit Does Not Turn ON

Detection condition: PS4 has turned ON, but PS5 does not turn ON within the expected time.

This indicates that the document has reached the scanning area but has not been detected at the exit section as expected.

Possible causes include:

  • Document stuck between the scanning area and output section.
  • PS5 actuator stuck or unable to move.
  • Contamination around PS5.
  • Sensor or wiring abnormality.

Check the post-scanning transport path and the PS5 actuator.

4.6 Error Code 66-21 – Duplex Reversing-Stage Detection

Detection condition: During the duplex reversing process, after the document has been reversed and PS3 turns ON, PS4 does not turn ON within the expected time.

This code is associated with the reversing-stage timing condition described for the DF-629.

When troubleshooting 66-21, pay particular attention to:

  • Document movement after reversal.
  • The reversing section.
  • The M4 reversing motor operation.
  • The transport path between the reversing section and PS4.
  • PS3 and PS4 sensor states during the second pass.

5. Duplex Reversal: Why Double-Sided Feeding Is More Complicated

The DF-629 uses a single-CCD reversing system.

After scanning the front side, the machine uses the M4 reversing motor to pull the document back into the reversing section. The document is then reversed and transported forward again to scan the back side.

The second forward feeding pass follows the sensor sequence:

<escape>PS2 → PS3 → PS4 → PS5</escape>

This means that PS2, PS3 and PS4 may be triggered again during duplex scanning.

Duplex Troubleshooting Considerations

The following points are important:

  1. A duplex jam does not necessarily mean that the reversing motor is defective.
  2. Sensor timing should be checked during both the first and second feeding passes.
  3. Codes 66-03, 66-13, 66-23, 66-33 and 66-04 may also occur during duplex feeding.
  4. Code 66-21 is the reversing-stage-specific condition described in this DF-629 troubleshooting information.

If simplex feeding works normally but duplex feeding repeatedly fails, inspect the reversing section and compare sensor I/O states during the second pass.

6. How to Check DF-629 Sensor I/O in Service Mode

The DFCB I/O screen allows technicians to monitor the sensor states directly.

I/O Check Path

Enter Service Mode and navigate to:

State Confirmation → I/O → DFCB

The sensor names are displayed as follows:

Sensor DFCB I/O Display Name
PS1 Document Empty
PS2 After Separate
PS3 Registration
PS4 Document Reading
PS5 Document Exit

Practical I/O Inspection

During troubleshooting:

  1. Open the DFCB I/O screen.
  2. Observe the sensor states before loading originals.
  3. Place originals on the document tray and check PS1.
  4. Start a document feeding operation.
  5. Observe the ON/OFF transitions of PS2, PS3, PS4 and PS5.
  6. Compare the actual transitions with the expected feeding sequence.
  7. For duplex problems, observe the sensor states during the reversal and second forward pass.

If a sensor remains ON or OFF when the document physically moves past it, inspect the sensor actuator, optical detection area, wiring and connector.

Safety note: Keep hands and tools away from moving rollers and reversing mechanisms during operation. Follow the applicable service safety procedures when observing live I/O states.

7. Quick Reference: DF-629 Sensor and Jam Code Cheat Sheet

Sensor Main Function Related Jam Code
PS1 Detects originals on the document tray No 66-series jam code
PS2 Confirms document separation 66-03
PS3 Controls document registration detection 66-13, 66-23
PS4 Detects document entering the scanning area 66-33, 66-21
PS5 Detects document exit 66-04

Easy Way to Remember the Five Sensors

  • PS1 – Document presence: Is there an original on the tray?
  • PS2 – Separation: Has the original passed the separation section?
  • PS3 – Registration: Has the original reached the alignment position?
  • PS4 – Reading: Has the original entered the scanning area?
  • PS5 – Exit: Has the original reached the output section?

The main forward transport sequence is:

PS2 → PS3 → PS4 → PS5

PS1 is only the preliminary document-presence detection sensor.

8. Frequently Asked Questions

How many sensors does the Konica Minolta DF-629 have?

The DF-629 configuration described in this guide uses five main document detection sensors: PS1, PS2, PS3, PS4 and PS5.

What does DF-629 error code 66-03 mean?

66-03 is associated with PS2, the After Separate sensor. It occurs when PS2 turns ON but does not turn OFF within the expected time.

Check for a document stuck around the separation section, a stuck actuator, sensor contamination or a sensor connection problem.

What is the difference between 66-13 and 66-23?

Both codes are associated with PS3, the Registration sensor, but their timing conditions are different.

  • 66-13: PS2 has turned ON, but PS3 does not turn ON in time.
  • 66-23: PS2 has turned OFF, but PS3 remains ON beyond the expected time.

What does DF-629 error code 66-33 mean?

66-33 indicates that PS3 has turned ON but PS4, the Document Reading sensor, does not turn ON within the expected time.

Inspect the document transport path between the registration and scanning sections.

What does error code 66-21 mean on the DF-629?

66-21 is associated with a specific duplex reversing-stage timing condition. After document reversal and PS3 detection, PS4 does not turn ON within the expected time.

Check document movement through the reversing section and the second forward feeding pass.

Why does the DF-629 work in simplex mode but jam in duplex mode?

Duplex scanning requires the document to be pulled back, reversed and transported through the scanning path again.

If simplex feeding works but duplex feeding fails, inspect the reversing mechanism, M4 motor operation and sensor timing during the second pass.

Where can I check the DF-629 sensor states?

Enter Service Mode and navigate to:

State Confirmation → I/O → DFCB

The screen displays the five sensor states using the names Document Empty, After Separate, Registration, Document Reading and Document Exit.

Conclusion

Understanding the five DF-629 sensors and their timing relationships makes ADF troubleshooting much more efficient.

The main forward feeding sequence is PS2 → PS3 → PS4 → PS5, while PS1 only detects whether originals are present on the document tray.

When a 66-XX jam code appears, identify the associated sensor and determine whether it failed to turn ON or OFF within the expected time. For duplex problems, remember that the document passes through the feeding path again after reversal, so sensor timing must also be checked during the second pass.

Using the DFCB I/O screen to monitor actual sensor transitions can help technicians locate the problem area before replacing components unnecessarily.

Technical Disclaimer: This guide is based on the DF-629 troubleshooting information for the Konica Minolta bizhub C368 configuration described here. Sensor timing, jam-code definitions and service mode functions may vary by machine configuration or firmware. Always confirm the applicable service documentation before performing repairs.